"Today, if you do not want to disappoint, Check price before the Price Up.Ar-15/m16 Upper Receiver Action Block Brownells You will not regret if check price." bargain Ar-15/m16 Upper Receiver Action Block Brownells
Heavy-duty blocks allow you to firmly clamp AR-15/M16 receiver halves in a vise without risk of crushing, twisting, or otherwise distorting them when applying vise pressure or torquing the barrel nut. Keeps your rifle secure for safe, effective cleaning, assembly, and repair. High pressure, solvent resistant, structural Rynite block and insert surround the entire upper receiver and support it inside and out to make rebarreling the AR-15/M16 an easy, one-man job. Lets you firmly secure a mil-spec carry handle receiver or mil-spec flattop receiver in a large bench vise for barrel removal/installation. Torque generated while tightening the barrel nut is transmitted to the block and insert, not the receiver. Minimizes the possibility of damage to the barrel detent pin and receiver detent notch. Holds securely without marring the finish.
DO NOT USE ON BILLET UPPERS OR LEFT HAND UPPERS, OR DAMAGE TO THE UPPER CAN RESULT.
SPECS: Injection-molded Rynite, black. Fits A1, A2, and standard flattop receivers. Block - 2.5" (6.3cm) thick, 3.5" (8.8cm) wide, 4.5" (11.4cm) high. Insert - 8" (20cm) long, 1" (2.5cm) diameter. Torque tested to 200 ft. lbs.
Heavy-duty blocks allow you to firmly clamp AR-15/M16 receiver halves in a vise without risk of crushing, twisting, or otherwise distorting them when applying vise pressure or torquing the barrel nut. Keeps your rifle secure for safe, effective cleaning, assembly, and repair. Unbreakable urethane vise block takes all the clamping force, so your expensive lower receiver won’t be damaged or distorted. Insert block into the magazine housing from the top or bottom, then clamp the other end in your bench vise. The magazine catch locks to the block, safely and securely holding the rifle for assembly, disassembly, cleaning, or repair. Will not mar or scratch the finish. Fits tightly in most receivers and may require filing to fit others.
SPECS: High-density urethane plastic, black. 5" (12cm) high, 2¼" (5.7cm) wide, ¾" (19cm) thick.
The BEV Block (Barrel Extension Vise) is an all-in-one, compact vise block tool for AR assembly operations of barrel nuts, flash hiders, etc. Mounts securely in a vise and provides support for both billet and forged upper receivers. Engages barrel extension with solid steel lugs and full length support shank to prevent flexing. Steel hardness is optimized for durability yet won't damage barrel extension, and Magpul Polymer is used for all other engagement surfaces to protect aluminum receiver. O-ring post uses bolt carrier for additional stability adn included pin keeps upper in proper position. The BEV can also be turned over and used as a mag well vise block to support the lower receiver during maintenance.
The Sinclair Vise Block is the perfect tool for securely holding your AR-15/AR-10® in a bench vise. The Vise Block inserts into your magazine well just like a magazine and the bottom half of the block can be clamped into a vise. You can tilt the block in the vise to work at a different angle if desired. You can also insert the vise block into the top of the lower assembly allowing you to work on the bottom side. The Vise Block is made of machined high density polyethylene, so it is extremely solid. Great workbench tool. AR-10® Model only fits Armalite® AR-10® pattern rifles, does not fit DPMS/SR25 pattern rifles.
Our bolt vise helps you disassemble your AR-15 bolt easily and without losing any parts. The main function of the tool is to compress the ejector so you can remove the spring pin easily. This enables you to release the pressure on the ejector slowly so the ejector and spring don't go flying off your workbench. The ejector and spring can be replaced if needed and the bolt reassembled easily. The tool cradles the bolt and holds it firmly in place while the screw assembly compresses the ejector. A hole in the vise allows the pin to drop free. The tool can also be used to hold the bolt securely while replacing gas rings and replacing the extractor. NOTE: We recommend you replace the ejector spring pin when reassembling if you have one available. A one sixteenth of an inch punch is required to remove the pin.
Machined from tough, long-wearing nylon to hold upper receiver in a bench vise without fear of crushing, marking or scratching the finish. Fits inside stripped or barreled, carry handle and flattop receivers with .250" diameter pivot pins. Holds receivers at any angle for cleaning, or fitting sights and accessories. Models to fit standard AR-15 and DPMS AR-style .308 receivers.
The Geissele Reaction Block is designed to aid in the assembly of lower receivers. Once the armorer has installed the buffer tube onto the lower; the buffer tube and lower receiver assembly can be slid into the Reaction Block at the 12, 3, 6 and 9 o’clock positions. This allows the armorer to rotate the lower in 90 degree increments in the block simply by loosening the provided nylon screws, removing the lower, and sliding it back in at the desired orientation. The Reaction Block provides an ultra-stable platform for performing an array of lower receiver operations, as well as making the installation of the buffer retainer nut quick and easy. All while keeping both hands of the armorer free to work, saving both time and frustration.
Heavy-duty vise block takes all the clamping force, so your expensive lower receiver won’t get scratched, distorted, or otherwise damaged. Insert block into the mag well, just like an ordinary magazine, then clamp the other end in your bench vise. The magazine catch locks to the block, safely and securely holding the rifle for assembly, disassembly, cleaning, or repair. Double-ended design fits ArmaLite® AR-10®, Bushmaster .308, DPMS Panther™ LR-308, and Remington R-25. Does not fit Rock River Arms lower receivers. Machined from rugged, durable, chemical-resistant Delrin® polymer; will not mar or scratch weapon’s finish.
SPECS: Machined Delrin, white. 5-1⁄8” (13cm) high, 3” (7.6cm) wide, 1” (2.5cm) thick. Fits most AR-Style .308 rifles except Rock River Arms.
This upper receiver armorer's block will allow the gunsmith or enthusiast to assemble, modify, or maintain most AR pattern modern sporting rifles. While most blocks will only fit one specific style, the XS Universal block provides the versatility need to work on any AR pattern upper receiver: AR-15, AR-10, SR25, or DMPS GII. This versatility, plus the reliability of an XS Sights Made in the USA aluminum product, is a one size fits all solution.
Professional Grade AR Upper Receiver Fixture. Robust fixture designed for years of hard use. Quick, intuitive interface that allows rapid building/rebuilding and repair of the entire upper receiver of the AR15/M16/M4 family of rifles/carbines/pistols. Designed to allow all upper receiver parts to be installed or removed without interference. Designed with rail systems in mind, the Device has clearance for most rail systems to allow installation and removal while the upper is securely held. Holds receiver from the inside via the bolt carrier raceway and charging handle raceway by way of a "T" interface. Front and rear lugs are controlled along with the entire bottom receiver flat. Compatible with milspec dimensioned receivers and billet receivers utilizing milspec internal dimensions. The Device does not contact barrel extension and is not caliber sensitive. Accurate Picatinny rail, with enumeration, allows for quick optic set-up or repair. A lanyard is provided to keep parts at-hand and help prevent dropping. An internal spring loaded detent allows for vertical application without loss of control. A2 and M4 rear sight tension spring alignment and removal is built in. Forward Assist removal channel in base. "Bolt carrier" style recesses allows Ejection Port door opening and testing.